TransPAC-6300AV   1553       DATA BUS  ANALYZER/SIMULATOR
Rugged Portable MIL-STD-1553A/B  Bus  Analyzer/ Simulator System                       

The TRANSPAC-6300AV provides the highest level of performance and flexibility for MIL-STD-1553A/B or MacAir protocols on the PCI bus. The TRANSPAC-6300AV is integrated with powerful software that reduces development time. All databus functionality is supported from our advanced API (Application Programming Interface). Standard features include IRIG/GPS synchronization capability, real-time bus playback (with ability to edit out RTs), aperiodic message insertion, error injection/detection, conditional BC branching, 48-bit timetags and “Oneshot” BC operation. The Bus Monitor mode provides 100% bus monitoring of fully loaded 1553 or MacAir buses.

Multi-function Interfaces

One or two multi-function interfaces are available on a Rugged field portable system. They can operate simultaneously as a BC, up to 31 RTs and as a BM. It can emulate an entire dual redundant channel internally, eliminating the need for external hardware to simulate missing nodes.

Single-function Interfaces

The TRANSPAC-6300AV can provide one or two single-function interfaces with all the features and functionality of the multi-function versions, but only one major operational mode is enabled at a time - emulating either a Bus Controller or 31 Remote Terminals or Bus Monitor.

Software Included with the TRANSPAC-6300AV is a flexible, high-level API which supports up to 10 independent 1553 channels. Windows XP, 2000, Me, NT, 98, 95, Linux, LabWindows/CVI, Visual Basic and source code is provided. VxWorks drivers are included. Solaris support available (both Intel and Sparc platforms). LabVIEW support and BusTools/1553, The software’s  GUI bus analysis, simulation and data logging solution for 1553, are optionally available. TransPAC-6300AV high performance and intuitive software solutions provide complete and simplified access to MIL-STD-1553 functionality for development, integration, test, embedded and maintenance applications.

Specifications

Physical

• Dimension (17.1” W x 11.2” H x 9.1” D)
• Display: 15” TFT Color LCD Display, 1024 x 768 XGA, SVGA resolution

Environmental

• 0°C to +70°C Operating Temperature
• 5 to 90% Relative Humidity (Non-condensing)
• Extended temperature range available

Power Supply (two channels, 50% duty cycle) : 110V/230V AC (Auto-switch): 300 Watts

• +5 VDC: 1.5 A
• +12 VDC: 222 mA
• -12 VDC: 50 mA

On-board Static RAM

• 1 MByte (per dual-redundant channel)

Connections

• Direct or transformer coupling (software controlled)
• Variable output voltage (software controlled)
• Transition cabling to 1553 cable jacks and subminiature coaxial BNC for I/O triggers provided

Multi-function Operational Modes

• Simultaneous Bus Controller, 31 Remote Terminals and Bus Monitor

Single-function Operational Modes

• Bus Controller or 31 Remote Terminals or Bus Monitor

Warranty:  1 year limited hardware warranty

Functional Highlights

Bus Controller

• Programmable control over:

- Major and minor frame content and timing
- Intermessage gap times
- Response time-out and late response

• Modify messages, data or setup while card is running
• Insert aperiodic messages into a running BC list
• "One-shot" mode for simplified BC operation
• Conditional message sequencing (branching) based on real-time message data or status
• Selectable interrupt generation and status messages:

- Full range of system conditions
- All detected errors
- Interrupt after "n" conditions

• Full error detection: Invalid word, late response, bit count error, early response, high word, low word, no response, inverted sync, incorrect RT address, manchester, parity error
• Extensive programmable error injection (on a per word basis)
• Synchronize BC operation to external time source

Remote Terminal

• Multiple RT simulation (up to 31 RTs)
• Modify data, status words or setup while card is running
• Extensive programmable error injection (on a per word basis)
• Programmable message content (linked message buffers)
• Selectable interrupts upon multiple conditions, including:

- End of message
- Major frame end
- Minor frame end
- Error conditions

Bus Monitor

• Capture 100% fully loaded bus traffic with:

- Time-tagging
- Error status for each word
- Word status
- Message status
- RT response time

• Interrupts can be selected by RT/SA/WC
• Large on-board memory storage
• Extensive filtering and triggering options:

- By individual RT/subaddress
- Transmit, receive or broadcast mode codes
- Internal or external triggering
- Trigger output on user sepcified data

• Real-time bus playback with RT edit mode
• 48-bit, microsecond resolution timetagging
• IRIG/GPS synchronization

Software Support

• API - Includes high-level libraries for Windows XP, 2000, Me, NT, 98, 95, Linux, LabWindows/CVI, Visual Basic and VxWorks. Source code API library provided
• BusTools/1553 - Optional GUI software for MIL-STD-1553 Bus Analysis and Simulation
• LabView - Optional support
• Solaris - Optional support (both Intel and Sparc platforms)

Specifications subject to change without notice.

TransPAC-6300 and TransPAC-6300AV are trademarks or Cepoint Networks,  LLC. All other Trademarks and copy rights are properties of their respective owners.

Cepoint  Networks, LLC. One West Otterson Street, Nashua, NH 03060,U.S.A. Phone: +1  (603)883-7979 Fax: + 1 (603)883-3266 E-mail: sales@cepoint.com Website: http://www.cepoint.com